Ontario FIT & MicroFIT Compliant Solar Mounting Hardware
Ontario FIT, MicroFIT Compliant Solar Mounting Hardware

IronRidge XRS Rail

IronRidge Ontario FIT and MicroFIT compliant solar mounting hardware

Model #
Qty
Length
Matrix Part #
51-7000-108A
1
9 feet
11-46-194
 

XRS Rails - Anodized Aluminum
IronRidge light rail in anodized finish.


XRS End Cap 11-46-219End Cap
Available for both Standard (XRS) and Light (XRL) Rails, end caps provide a finished look while protecting against the collection of water and debris inside the rail. End caps are cast from black polycarbonate with UV protection.


# 11-46-219 XRS End Cap - Specify as Ontario FIT Compliant Version

 

IronRidge end clamp

 

 

End Clamps
Clamp type is based on your solar module used.

Model #
Description
Qty
Product #
29-7000-125
End Clamp for 31 - 33 mm modules 
4
11-46-216
29-7000-134
End Clamp for 33 - 35 mm modules 
4
11-46-170
29-7000-224
End Clamp for 35 - 37 mm modules 
4
11-46-171
29-7000-157
End Clamp for 39 - 41 mm modules 
4
11-46-213
29-7000-160
End Clamp for 40 - 42 mm modules 
4
11-46-196
29-7000-171
End Clamp for 42 - 44 mm modules 
4
11-46-215
29-7000-214
End Clamp for 45 - 47 mm modules 
4
11-46-190
29-7000-204
End Clamp for 49 - 51 mm modules 
4
11-46-214

 

IronRidge mid clamps

 

Mid Clamps
Each clamp kit listed below contains four clamps and the associated hardware.

Model #
Description
Qty
Product #
29-7000-105
Mid Clamp for 37 mm thick ,or less, modules 
4
11-46-173
29-7000-101
Mid Clamp for 39 - 41 mm thick modules 
4
11-46-174
29-7000-101
Mid Clamp for 40 - 44 mm thick modules 
4
11-46-197
29-7000-108
Mid Clamp for 45 - 51 mm thick modules 
4
11-46-191


IronRidge internal splice

Internal Splice
Order one internal splice (internal splice bar and hardware) where two lengths of rail need to be joined.

Model #
Splice Type
Matrix Part #
29-7000-010
XRS Splice
11-46-176

 

IronRidge L-Feet

L-Feet
One L-feet kit contains 4 individual L-feet and hardware.

Model #
Qty
Matrix Part #
29-7000-017
4
11-46-178

Important Note:
Maximum c/c spacing:
XRS Rail, 2.7 m
XRL Rail, 1.5 m

Lambda Light for Flat Roof

Lambda LightLambda Light for Flat Roof, a unique low-ballasted system, has been developed for use on flat roof and industrial buildings with low load tolerances. It is extensive aerodynamic testing. This economical system requires no roof penetration, and because components are preassembled and few tools are needed it is quick and easy to install.

All components of the Lambda Light are made of either aluminum or stainless steel. Their high resistance to corrosion ensures long service life and complete recyclability.

Ten year warranty.

Support legers Lambda pour toit plat • Designed for low load bearing flat roof
• Versatile, lightly ballasted
• For framed modules
• Standard with 15˚ pitch
• Wind guard to reduce wind loading
• Rapid installation with high levels of: Pre-fitting and pre-assembly
• Typical distributed rooftop load: *3 - 5 lbs/ft2
• Individual planning and project support minimum 25 module systems
System includes: Framing, wind guard and fasterners Mat Roof Protection

*Ballast as specified by a structural engineer.

pour toit plats Lambda Light pour toit plats Lambda Light pour toit plats


 

Quick Mount PV Mount Flashing
MicroFit, FIT compliant, Ontario

Quick MOunt PV - all-in-one waterproof flashing and mountQuick Mount PV

Quick Mount PV mount flashing
is an all-in-one waterproof flashing and mount to anchor photovoltaic racking systems and solar thermal panels, for a new or existing roof. It is made of aluminum and includes stainless steel hardware. It works with all standard racks, installs seamlessly and saves labour by not needing to cut away any roofing, will out live galvanized 2 to 1, and is a better low-profile mount.

The units are sold in 12 packs. Each 12 pack includes the mounting hardware and the mount with flashing to install 12 mounts, with written instructions.


Product #
Model
Description
11-83-001
QMSCA12
Composition Mount, 12 X 12, Mill Finish (12)
11-83-002
QMSCB12
Composition Mount, 12 X 12, Bronze Finish (12)
11-83-003
QMCCA12
Conduit Compositon, Mount, 9 X 12, Mill Finish (12)
11-83-004
QMCCB12
Conduit Compositon, Mount, 9 X 12, Bronze Finish (12)
11-83-005
QMHS612
6 Hanger Bolt Set (12) "
11-83-006
QMHS812
8 Hanger Bolt Set (12) "
11-83-007
QMHS1012
10 Hanger Bolt Set (12) "

 

HES PV Toll Free: 1.866.258.0110